Live action from FUMANCHU182.

[fumanchu182]

Keep us updated.

Install tutorial starts right now. Step 1 remove the lower temperature radiator.

Step 2 install support brackets for chiller. Tools required: 8mm, 10mm and 13mm sockets or wrenches. Swearing optional. Start with the smaller bracket, leave some what loose til final tightening sequence.



Attach cross bracket, take note of logo placement and holes the bolts are placed in.

My tightening sequence was rear bolt, front bolt, connector bolt. Attach chiller brick from below and start the middle nut.

the rear nut was the biggest pain in the ass to get started and tight. This is where swearing is recommended. I created a new one: dildo-headed-cock-fucker.

I have attached LTR removal instructions from the FSM.

 

[BULL]

Install tutorial starts right now. Step 1 remove the lower temperature radiator.
View attachment 93244 View attachment 93245
Step 2 install support brackets for chiller. Tools required: 8mm, 10mm and 13mm sockets or wrenches. Swearing optional. Start with the smaller bracket, leave some what loose til final tightening sequence.

View attachment 93246
View attachment 93247
Attach cross bracket, take note of logo placement and holes the bolts are placed in.
View attachment 93249
My tightening sequence was rear bolt, front bolt, connector bolt. Attach chiller brick from below and start the middle nut.
View attachment 93248
the rear nut was the biggest pain in the ass to get started and tight. This is where swearing is recommended. I created a new one: dildo-headed-cock-fucker.
View attachment 93250
I have attached LTR removal instructions from the FSM.

Does the LTR go back in?

 

[fumanchu182]

Does the LTR go back in?

No, permanently gone. The IC system is an always on system. With the KC I could have gone this route as well but choose not to. I regret that decision, it was like trying to stuff 20 lbs of shit in a 5lb bag with the limited room.

 

[fumanchu182]

All righty did a test fit with the bumper and cursing worse than given watch right before a shore visit...

Try number three

Absolutely seething at this point, texted @RGPIII that I might not run a bumper. Stepped back, meditated for ten minutes. Found my fucking zen...

Mounted on the above hole and wouldn't you fucking guess it.

While under here decided to mock up hoses and index the inlet port.

Did one final sanity check to make sure the AC fittings would get past the pump.

Hope this helps anyone from having a fitment issue. Moved onto the 3 way bypass. Since IC Chiller is always on the default is to send it right back to the pump. However for winter driving the IC system reverses the main SC condensers flow naturally it is exiting here but we are changing that.



The above is the SC outlet routed to the bypass.

 

[RGPIII]

I will for sure be changing to Soft lines on mine to make it more direct and less routing the next time I have it apart for anything.

 

[jonx96]

@fumanchu182 I'd appreciate if you made your own install thread for this so I can go back and reference it if I do one.

 

[vortecd]

I agree. I know you have an on going build thread but would be helpful to make this its own thread

 

[RGPIII]

guys the plug and play kit is really very simple to install. once you do it, you'll be very surprised at how simple it was.

 

[vortecd]

guys the plug and play kit is really very simple to install. once you do it, you'll be very surprised at how simple it was.

I'm not very smart though

 

[fumanchu182]

I'm not very smart though

We know... 😂 I'll keep this thread running and then compile at the end. Not like any of you are installing any time soon.

 

[jonx96]

We know... 😂 I'll keep this thread running and then compile at the end. Not like any of you are installing any time soon.

You never know what I’m going to do 🤣 I may or may not purchase a bare block

 

[vortecd]

You never know what I’m going to do 🤣 I may or may not purchase a bare block

Yep I can tell you Jon could buy a different engine, trailer, car, supercharger, chiller, nitrous at any given moment. I dont think he even knows what he is doing next

 

[jonx96]

Yep I can tell you Jon could buy a different engine, trailer, car, supercharger, chiller, nitrous at any given moment. I dont think he even knows what he is doing next

I’m happy with the trailer for now. A 28 ft would be nice tho 🤣
Funny thing is you have known me long enough I’m not just talking I very well will end up buying anything I say I’ll buy

 

[RGPIII]

I’m happy with the trailer for now. A 28 ft would be nice tho 🤣
Funny thing is you have known me long enough I’m not just talking I very well will end up buying anything I say I’ll buy

I will say my 28FT trailer is the perfect length with my hellcat in it.

 

[fumanchu182]

Some progress, trials and tribulations. First off Fuck Dodge in all holes with dirty syringes. This hose is from the back of the coolant pump.

It necks from 1" to 7/8 instead of 3/4. Trying to get a pushlock to work was insanity. Solution was this hose.

Cut this much off from the long end. 2.75"

Afterwards easy day.


Use a 1" to 3/4 reducer and a 3/4 hose elbow.
Them on the 3 way great progress with the 150* fitting.

Dumps down beautifully.

Will be adding the final AN pushlocks soon. More to come!

 

[fumanchu182]

ran some vibrant extremewrap
The above is my drain point, 12an union.
Neatly tucked if I do say so myself.
Fabbed up some aluminum mounts
Started running the IC exit to the bmr tank



for the more cramped spaces I need some more vibrant wrap but ran out this might be a monday thing as the speed shop is closed

 

[Smitty]

Yep I can tell you Jon could buy a different engine, trailer, car, supercharger, chiller, nitrous at any given moment. I dont think he even knows what he is doing next

Sounds like he’s got a disease. He isn’t stable. 😂 Might want to keep an eye on him. 😂

 

[jonx96]

@fumanchu182 I know you are always up for a good time. Want to go in on a nitrious kit with me so I can be a dealer If we start at a 100 shot im sure we will be fine

 

[DavidKFla]

I’m happy with the trailer for now. A 28 ft would be nice tho 🤣
Funny thing is you have known me long enough I’m not just talking I very well will end up buying anything I say I’ll buy

28 footer is still a bit short. I would recommend a 34' triaxle.

 

[fumanchu182]

Absolutely not. 😂

@fumanchu182 I know you are always up for a good time. Want to go in on a nitrious kit with me so I can be a dealer If we start at a 100 shot im sure we will be fine